14MZ MANUAL PDF

14mz, Instruction manual • Read online or download PDF • Futaba 14MZ User Manual. Get Futaba 14MZ Manual. Get all Futaba manuals! 14MZ. 14 CHANNEL RADIO CONTROL SYSTEM. PCMG3/PCM/FM selectable. INSTRUCTION. Compact Flash (CF) Card Handling Instructions Follow these precautions when handling the CF card included in your 14MZ transmitter. DO NOT allow the.

Author: Kajihn Maubei
Country: Turkmenistan
Language: English (Spanish)
Genre: Marketing
Published (Last): 1 October 2006
Pages: 353
PDF File Size: 20.53 Mb
ePub File Size: 18.72 Mb
ISBN: 495-9-55193-523-6
Downloads: 7996
Price: Free* [*Free Regsitration Required]
Uploader: Voodooshura

FUTABA 14MZ Instruction Manual

Definitions of Symbols Pay special attention to safety where indicated by the following symbols. Adjust the screw on the right. Make sure that the security mode is “User’s name”, and then push maual User ID button. Snap Roll [Corresponding model type]: Pitch to RUD mixing curve Normal Use the hovering system and set this curve to match take off and landing and vertical climb at a constant speed. Do not use any other chargers except CR that is for 12V application to charge the LT2F battery through this connector.

Touch the center of the cross hair cursor on the screen with the stylus pen. Complete a full range check. Navigate through menus and make selections by touching the screen or using the Dial-N-Key button. If you continue pressing it, the trim position starts to move faster.

Maanual not attempt to charge Li-Ion batteries with a charger that is NOT designed for Li-Ion batteries, as permanent damage to the battery and charger could result. Open the dust protection cap on the back of the transmitter that is covering the hole for throttle stick adjustment. Rates are adjusted simultaneously. Touch the button of the mixing you want to set. As the CF card is a precision device, do not use excessive force when inserting.

Use your finger or included stylus pen to operate the touch screen. Never remove the CF card or turn off power while entering data. Page 71 Data Reset Model memory setting data reset.

Rates are adjusted separately. When the left side button is touched, the backlighting becomes darker. All programming and setup may be done in this manner without transmitting. Download old software from here: Insert the switch block so that it fits correctly into the body of the transmitter as shown in the picture and use the hexagonal wrench to tighten the screws.

The servos operate smoothly at a constant speed corresponding to the set speed.

Futaba 14MZ Manuals

It is like hearing the same sentences about heading hold gyro many years ago Page V-tail [Corresponding model type]: Then slide the card into the slot until the card touches bottom. Refer to it when setting each function.

Idle Down Lowers the engine idling speed. A curve setting manuao is shown below. Later setting resets the data set by mixing function, etc. The start-up time may be a little bit slower when the CF card is installed compared to when the card is not.

You will do this five times.

Receiver and servos connection | Futaba 14MZ User Manual | Page 45 /

Two transmitters must be connected by an manua Trainer Cord, and the Instructors transmitter should be programmed for trainer operation, as described below. Pulse width control, 1. Remember that this program is for FX40 and what will happen if you change stick mode? Monitor the charge area with a smoke or fire alarm, and have a lithium-approved “ABC type” fire extinguisher available at all times.

DO NOT allow the battery’s internal electrolyte to get into eyes or on skin–wash affected areas immediately if they come in contact with the electrolyte.

Futaba 14MZ User Manual

Push the “Yes” button after confirming the ID. The End Point function adjusts the left and right servo throws, generates differential throws, and will correct improper linkage settings.

Frequency Frequency Band frequency setting, modulation mode setting, receiver ID code setting. 114mz the screw on the left. Use your finger or included stylus pen to operate the touch screen. Clock This shows the today’s date and the current time. The winglet is a vertical or angled extension at the tips of each wing. Push the file name to select the music file you want to hear.

Page 27 new frequency data is displayed. Manuall Programmable mixing includes a powerful link function, which allows Programmable mixing to be linked with the special mixing functions, or with other programmable mixing functions. Futaba is not responsible for unauthorized modification, adjustment, and replacement of parts on this product.

Page 70 Dial Monitor LDisplays the position of the dials, slider levers, and digital trim. When you also want to input the same setting contents at other conditions, perform setting in the group mode initial setting.