ASTM C203 PDF

ASTM Standards: C Test Methods for Cold Crushing Strength and Modu- lus of Rupture of Refractories2. C Terminology Relating to Thermal. GeoTesting Express is a provider of Geosynthetic Testing Services – ASTM C, Standard Test Methods for Breaking Load and Flexural Properties of. Meets ASTM C – ASTM C – 05a. Standard Test Methods for Breaking. Load and Flexural Properties of Block-. Type Thermal Insulation.

Author: Gakinos Faerr
Country: Rwanda
Language: English (Spanish)
Genre: Career
Published (Last): 15 September 2005
Pages: 385
PDF File Size: 19.90 Mb
ePub File Size: 2.80 Mb
ISBN: 275-6-41595-586-8
Downloads: 93856
Price: Free* [*Free Regsitration Required]
Uploader: Brami

It is also applicable to cellular plastics. This standard is also available to be included in Standards Subscriptions. Test Method I has a high shear stress component in the direction of loading, perpendicular to the axial fiber stress.

In comparing results it is important that all parameters be equivalent. The equations used are based on the assumption that the materials are uniform and presume that the c23 characteristics below the elastic limit are linearly elastic.

Active Risk Management

It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. It is important that the user consult ast appropriate materials specification for any specific detailed requirements regarding these test methods.

Historical Version s – view previous versions of standard. Used for breaking load measurements only.

Test Method I has a high shear stress component in the direction of loading, perpendicular to the axial fiber stress. We have no amendments or corrections for this standard. Increases in the strain rate typically result in increased strengths and in the elastic modulus.

Link to Active This link will always route to the current Active version of the asttm. The equations used are based on the assumption that the v203 are uniform and presume that the stress-strain characteristics below the elastic limit are linearly elastic. Used for breaking load measurements using a fixed crosshead speed machine. The values given in parentheses are provided for information only. These assumptions are not strictly applicable to thermal insulations of certain types in which crushing occurs before failure is obtained v203 transverse bending; however, depending upon the accuracy required, these procedures are capable of providing acceptable results.

Used for breaking load measurements using a fixed crosshead speed machine. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

It is important that the user consult the appropriate materials specification for any specific detailed requirements regarding these test methods.

In comparing results it is important that all parameters be equivalent. Two test c23 are described as follows: It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

Values are measured at the atsm load or breaking point under specified conditions or specimen size, span between supports, and rate of load application. The maximum axial fiber stresses occur on a line under the loading fitting in Test Method I and over the area between the loading fittings in Test Method II.

ASTM C203 Flexural Bend Fixture for Foam & Thermal Insulation | GC203-238

Increases in the strain rate typically result in increased strengths and in the elastic modulus. You may delete a document from your Alert Profile at any time.

The maximum axial fiber stresses occur on a line under the loading fitting in Test Method I and over the area between the loading fittings in Test Method II. Flexural properties determined by these test methods are also useful for quality control and specification purposes. Two test methods are described as follows: If the document is revised or amended, you will be notified by email.

ASTM C Flexural Bend Fixture for Foam & Thermal Insulation | GC

Used for breaking load measurements only. It is also applicable to cellular plastics. For specific precautionary statements, see Section These test methods cover the determination of the breaking load and calculated flexural strength of a rectangular cross section of a preformed block-type thermal insulation tested as a simple beam.

There is no comparable shear component in the central region between the loading fittings in Test Method II. Please first log in with a verified email before subscribing to alerts. Work Item s – proposed revisions of this standard. Proceed to Checkout Continue Shopping. Your Alert Profile lists the documents that will be monitored.

Subscription pricing is determined by: This information is useful for quality control inspection and qualification for specification purposes. As the voice of the U.