INTERCOM USING LM386 PDF

13 Aug AM-FM radio amplifiers; Portable tape player amplifiers; Intercoms; TV sound systems; Line drivers; Ultrasonic drivers; Small servo drivers. Browse through a total of 9 LM Circuits and projects. In this intercom schematic, the 8 ohm speakers is used as microphone and listening speaker. LM In this intercom schematic, the 8 ohm speakers is used as Intercom circuit diagram. intercom . This website uses cookies to improve your experience.

Author: Zulugore Merr
Country: Pakistan
Language: English (Spanish)
Genre: Technology
Published (Last): 8 November 2008
Pages: 403
PDF File Size: 4.20 Mb
ePub File Size: 13.89 Mb
ISBN: 883-3-51347-861-6
Downloads: 43845
Price: Free* [*Free Regsitration Required]
Uploader: Kazigar

Building a circuit on a breadboard November 8, Am doing a project on loadshedding time management using programmable interface.

Intercom circuit using lm386

The circuit can also run on voltage between 5V to 12V so choose a power supply which you are comfortable with. Apr 26, 5. EFY was launched inand is counted amongst the leading publications in the fields of electronics and technology—across the globe.

It is important that there is no acoustical intercok between the microphone and the loudspeaker on both the sides.

LM electronic intercom circuit

The LM has a gain range from ; by default the value of gain is 20 but can be increased upto by using a capacitor across the pins 1 and 8.

How to use Mhz RF transmitter and receiver modules with arduino June 14, What is the output current. ITS working fine, but the Kind of waves it producing as output as not sinusoidal wave. How much supply vtg to give for the circuit. Pin 2 is the negative input terminal, connected to the ground.

Can I use this design as stereo amplifier; I mean dual channel amplifier. HelloI’ve made this intercom circuit and it works just fine, however, i want to make it wireless but i don’t know howany ideas? For power supply, you can use an AC-DC wall adaptor, dry batteries or rechargeable batteries.

How to use the DIY clap switch September 16, Hope you understood the project and got it working, if not feel free to use the comment section or the forums to post your doubt and I will try my best to resolve it.

The preferred power supply for the circuit is 6V or above but the circuit also works with regulated 5V from IC not shown in the diagram. It would be about mA, check LM datasheet for more info.

Audio amplifier using LM386

In this case the loudspeaker must be ingercom by a crystal earphone, what changes must I make in the circuit? These are just like landline phones but, you do not need an operator, the voice received from one end will be directly transferred to the receiver on the other end.

I a help of any one immediately. Please enter your name here. PIN 1 and 8: Apr 26, 2. Kntercom resistor R2 is used to control the volume of the speaker; here I have limited the volume to medium level using a 4. Hello, I am using this circuit for an electronic stethoscope. Potentiometer acts as volume control knob. You can also upgrade this project by adding another SPDT switch to turn of the speaker on your side when you are talking.

Apr 26, 7. It has two simple and identical channels—unit 1 and unit 2. You om386 use the amplifier module for your project. If a higher dynamic range is needed, the power supply should be 9V or even 12V.

We just need a 3. A low cost LM based Audio Amplifier is available on www. A suitable resistor should be used for l,386 working of mic, you can look up to datasheet for the value or use a variable resistor and set the proper value. The audio amplifier amplifies the sound of FM receiver.

Circuit diagram and the photograph you kept are different in connections.

Get Our Weekly Newsletter! Instead of a speaker, there is an audio jack to which any earphones can be plugged in. And another question is if there is an amplifier whose gain starts from 1 and is adjustable, please tell me its name. These are the gain control PINs, internally the gain is nitercom to 20 but it can be increased up to by using a capacitor between PIN 1 and 8.